Professional Industrial Automation [LIVE CLASS]

About Course

Automation School-এর PLC | VFD | HMI & Industrial Motor Control কোর্সটি এমনভাবে ডিজাইন করা হয়েছে যাতে একজন শিক্ষার্থী একদম বেসিক থেকে শুরু করে ধাপে ধাপে ইন্ডাস্ট্রিয়াল অটোমেশন সেক্টরে কাজ করার মতো বাস্তব দক্ষতা অর্জন করতে পারে।

এই কোর্সে আপনি শিখবেন Industrial Motor Control, Control Panel Wiring, PLC Programming, VFD Setup & Configuration, HMI Screen Design, Sensor Application এবং Factory Troubleshooting-এর গুরুত্বপূর্ণ বিষয়গুলো। প্রতিটি ক্লাস লাইভ ও প্র্যাকটিক্যাল ভিত্তিক হওয়ায় আপনি শুধু থিওরি নয়, হাতে-কলমে কাজ শিখতে পারবেন।

কোর্সে Delta PLC, Mitsubishi PLC, Siemens S7-200 PLC, Siemens S7-1200/S7-1500, Delta HMI, Delta VFD সহ ইন্ডাস্ট্রিতে বহুল ব্যবহৃত ডিভাইস ও সফটওয়্যার ব্যবহার করে প্রশিক্ষণ দেওয়া হবে। ফলে স্থানীয় ও আন্তর্জাতিক চাকরির বাজারে কাজের জন্য নিজেকে প্রস্তুত করতে পারবেন।

যারা Electrical, Electronics, Mechanical, Mechatronics, IPE ব্যাকগ্রাউন্ড থেকে এসেছেন, কিংবা Factory Maintenance, Automation Job, Control Panel Design অথবা Freelancing Skill শিখতে চান, তাদের জন্য এই কোর্সটি খুবই উপযোগী।

Identify, test, and wire major industrial control devices such as contactors, relays, timers, overload relays, sensors, and SSR.
Design and troubleshoot DOL starters, Star-Delta starters, interlocking circuits, and forward-reverse motor control panels.
Program Delta PLC (DVP Series) using Ladder Logic and Function Block Diagram (FBD) in WPLSoft / ISPSoft.
Use essential PLC instructions including timers, counters, data registers, arithmetic, move, compare, and analog I/O.
Configure and commission Delta VFD for motor speed control through keypad, analog signal, and Modbus communication.
Design professional HMI screens in DOPSoft with buttons, indicators, alarms, trends, and data logging features.
Integrate PLC + VFD + HMI into a complete industrial automation control system.
Apply overload protection, phase protection, and safety interlocking in real industrial applications.
Gain practical knowledge of Mitsubishi and Siemens PLC systems for wider career opportunities.
Develop job-ready troubleshooting skills for factories and industrial automation systems.

Course Content

MODULE 1 – Industrial Manual Controlling

Class 1 : Introduction & Device Overview

01:36:49
Class-2 Different Types Switch, Electromagnetic Relay Test & Measurement by Multimeter

01:56:14
Class-3 : Electromagnetic Relay Wiring Techniques & Functionality

01:27:37
Quiz: Switch & Electromagnetic Relay
Class-4 : Magnetic Contactor and DOL Starter Definition, Selection, Working Principle, Power & Control Circuit

01:38:36
Quiz: Magnetic Contactor & DOL Starter
Class-5 : Thermal Overload Relay (OLR) & Phase Failure Relay Wiring Techniques & Functionality

01:59:23
Quiz: Thermal Overload Relay (OLR) & Phase Failure Relay
Class-6 : Timer Relay Basics, Wiring Techniques, Functionality & 3 Phase Motor Control

01:54:29
Quiz: Timer Relay Basics, Wiring Techniques, Functionality & 3-Phase Load Control
Class-7 : 3-Phase Load (Motor) Control Based on Time Part-2
Assignment-1 3-Phase Load ON (Motor) Control Based on Time
Class-8 : Interlocking & Manual Reverse-Forward
Class-9 : Auto Star-Delta Starter
Class-10 : Sequential Motor Control – Part 1
Class-11 : Sequential Motor Control – Part 2
Class-12 : Auto Reverse-Forward
Class-13 : Water Pump Control
Class-14 : Digital Sensor & Counter
Class-15 : Analog Sensor & Temperature Controller

MODULE 2 – Programmable Logic Controller (PLC) – Delta

Class-16 : Introduction to PLC
Class-17 : PLC Internal Architecture
Class-18 : Delta PLC Hardware
Class-19 : Software & Fundamental Commands
Class-20 : Timer & Counter Instructions
Class-21 : Memory – General, Latched, SET/RESET
Class-22 : Data Registers & Edge Triggers
Class-23 : Arithmetic & Move Commands
Class-24 : Block Move, Fill Move & Call Jump
Class-25 : Compare & Math Programming
Class-26 : Analog I/O in PLC
Class-27 : Program Upload & Download
Class-28 : Automatic Car Parking System Project
Class-29 : Automatic Compressor Control Project Explanation
Class-30 : Multiple PLC Projects – Simulation

MODULE 3 – Programmable Logic Controller (PLC) – Mitsubishi

MODULE 4 – Programmable Logic Controller (PLC) – Siemens S7-200

Class-38 : Introduction to Siemens S7-200
Class-39 : Bit Logic & Latching
Class-40 : Timers – Multiple Types
Class-41 : Counters – Up/Down
Class-42 : SET/RESET Instructions
Class-43 : Comparator Operations with Timer & Counters
Class-44 : Data Registers & Block Move
Class-45 : Math Functions
Class-46 : Conversion Operations
Class-47: Analog I/O & Practice

About Course

What Will You Learn?

Course Content

MODULE 1 – Industrial Manual Controlling

Class 1 : Introduction & Device Overview

Class-2 Different Types Switch, Electromagnetic Relay Test & Measurement by Multimeter

Class-3 : Electromagnetic Relay Wiring Techniques & Functionality

Quiz: Switch & Electromagnetic Relay

Class-4 : Magnetic Contactor and DOL Starter Definition, Selection, Working Principle, Power & Control Circuit

Quiz: Magnetic Contactor & DOL Starter

Class-5 : Thermal Overload Relay (OLR) & Phase Failure Relay Wiring Techniques & Functionality

Quiz: Thermal Overload Relay (OLR) & Phase Failure Relay

Class-6 : Timer Relay Basics, Wiring Techniques, Functionality & 3 Phase Motor Control

Quiz: Timer Relay Basics, Wiring Techniques, Functionality & 3-Phase Load Control

Class-7 : 3-Phase Load (Motor) Control Based on Time Part-2

Assignment-1 3-Phase Load ON (Motor) Control Based on Time

Class-8 : Interlocking & Manual Reverse-Forward

Class-9 : Auto Star-Delta Starter

Class-10 : Sequential Motor Control – Part 1

Class-11 : Sequential Motor Control – Part 2

Class-12 : Auto Reverse-Forward

Class-13 : Water Pump Control

Class-14 : Digital Sensor & Counter

Class-15 : Analog Sensor & Temperature Controller

MODULE 2 – Programmable Logic Controller (PLC) – Delta

Class-16 : Introduction to PLC

Class-17 : PLC Internal Architecture

Class-18 : Delta PLC Hardware

Class-19 : Software & Fundamental Commands

Class-20 : Timer & Counter Instructions

Class-21 : Memory – General, Latched, SET/RESET

Class-22 : Data Registers & Edge Triggers

Class-23 : Arithmetic & Move Commands

Class-24 : Block Move, Fill Move & Call Jump

Class-25 : Compare & Math Programming

Class-26 : Analog I/O in PLC

Class-27 : Program Upload & Download

Class-28 : Automatic Car Parking System Project

Class-29 : Automatic Compressor Control Project Explanation

Class-30 : Multiple PLC Projects – Simulation

MODULE 3 – Programmable Logic Controller (PLC) – Mitsubishi

Class-31: Introduction to Mitsubishi PLC

Class-32 : Software & Fundamental Instructions

Class-33 : Timer & Counter

Class-34 : Data Registers, Edge Triggers & Math

Class-35 : Move & Block Move

Class-36 : Compare & Jump Commands

Class-37 : Analog I/O

MODULE 4 – Programmable Logic Controller (PLC) – Siemens S7-200

Class-38 : Introduction to Siemens S7-200

Class-39 : Bit Logic & Latching

Class-40 : Timers – Multiple Types

Class-41 : Counters – Up/Down

Class-42 : SET/RESET Instructions

Class-43 : Comparator Operations with Timer & Counters

Class-44 : Data Registers & Block Move

Class-45 : Math Functions

Class-46 : Conversion Operations

Class-47: Analog I/O & Practice

MODULE 5 – Human Machine Interface (HMI) – Delta

Class-48 : Delta HMI Overview & Design Part 1

Class-49 : HMI Design – Part 2

Class-50 : HMI Upload, Download & PLC link

Class-51 : Factory Based HMI & PLC Projects

MODULE 6 – Variable Frequency Drive (VFD) – Delta

Class-52 : Introduction to VFD

Class-53 : VFD Working Principle

Class-54 : VFD Hardware Connection & Parameter Setting

Class-55 : VFD Parameter Setting

Class-56 : Advanced VFD Operation

MODULE 7 – PLC – SIEMENS (S7-1200/S7-1500) – TIA Portal & WinCC SCADA

Class-57 : Introduction to TIA Portal and Basic Programming

Class-58 : Advanced PLC Programming

Class-59 : HMI Development using WinCC (TIA Portal)

Class-60 : Communication & Networking